McLED

Regulations

Power Integrations Awarded Double Damages in Patent-Infringement Case Against Fairchild Semiconductor

Power Integrations today announced that a federal district court has doubled the financial damages awarded to the company in its patent-infringement case against Fairchild Semiconductor. This action follows an earlier ruling in which the Court found that Fairchild's infringement of Power…

LED professional Editors

LED professional

Fairchild was found to infringe four Power Integrations patents following a 2006 jury trial in the U.S. District Court for the District of Delaware. In 2008, following rejections of Fairchild's challenges to the validity and enforceability of the patents, the Court awarded Power Integrations approximately $6 million in damages and issued a permanent injunction against more than 100 infringing Fairchild products. The Court issued its willfulness finding in July 2010, paving the way for enhancement of the damages. The results of the case remain subject to appeal.

Commented Balu Balakrishnan, president and CEO of Power Integrations: "We are gratified that the Court has held Fairchild accountable for knowingly violating our patents and attempting to profit from the innovations that have made us the leaders in our market."

Two separate lawsuits filed by Power Integrations against Fairchild in May 2008 and November 2009 remain pending. The suits allege infringement of five Power Integrations patents, including two of the same patents previously found to be infringed in Delaware and one patent previously found to be infringed in Power Integrations' ITC case against System General, now a Fairchild subsidiary. The company is seeking additional damages as well as injunctions against the infringing products not subject to the existing injunction.

About Power Integrations:
Power Integrations is the leading supplier of high-voltage analog integrated circuits used in energy-efficient power conversion. The company's innovative technology enables compact, energy-efficient power supplies in a wide range of electronic products, in AC-DC, DC-DC and LED lighting applications. Since its introduction in 1998, Power Integrations' EcoSmart™ energy-efficiency technology has saved an estimated $4.6 billion of standby energy waste and prevented millions of tons of CO2 emissions. The company's Green Room ( www.powerint.com/greenroom) provides a wealth of information about "energy vampires" and the issue of standby energy waste, along with a comprehensive guide to energy-efficiency standards around the world. Reflecting the environmental benefits of EcoSmart technology, Power Integrations is included in clean-technology stock indices sponsored by the Cleantech Group (Amex:CTIUS) and Clean Edge (Nasdaq:CELS). For more information, please visit http://www.powerint.com/.

Did you like this article?

Share this article

You could also like this

Regulations

DALI Part 151 certification reaches products, targets surge protection for outdoor lighting

DALI Part 151 has moved from specification into certified products, giving manufacturers a defined framework for surge protection of DALI control devices exposed to induced electrical transients in outdoor lighting.

Regulations

UK now allows approved LED replacement bulbs in MOT tests

From 14 October 2026, MOT testers must accept ECE approved LED replacement (LEDr) bulbs fitted in compatible halogen headlamp units on class 3, 4, 5 and 7 vehicles. The change does not apply to class 1 and 2 motorcycles, halogen units converted for HID bulbs, or full LED headlamp unit replacements. Approved LEDr products must carry a permanent, secure approval sticker on the vehicle visible during the MOT. Testers need only check the presence and condition of this sticker and must fail the headlamp where the sticker is missing, unreadable, appears tampered with, or does not match the fitted bulb.

Regulations

IEC 60598-2-24:2026 published — updated requirements for limited-surface-temperature luminaires

The new edition of IEC 60598-2-24:2026 has been officially published. It specifies essential safety requirements for luminaires intended for use where combustible dust or flammable materials are present, necessitating strict control of enclosure surface temperatures to prevent fire or ignition. The revision aligns test methods and construction requirements with recent developments in industrial and specialist lighting and with the latest edition of the general standard CEI EN 60598-1:2024. Publication of the EN and subsequent CEI standard will follow as formal steps, after unanimous positive votes. ASSIL members can contact the Technical Area for clarification.

Regulations

The EU Energy Performance of Buildings Directive (EPBD) Is Coming

Europe aims to become climate-neutral by 2050 under the European Green Deal. A key pillar of this initiative is the revised European Energy Performance of Buildings Directive (EPBD), which all 27 EU Member States are required to implement beginning in 2026.

Luminuscree ledEdison optoTE connectivityLTF TechnologyLoreos

The latest Press Releases

Explore All

Stay current with our monthly Update from the lighting industry

LEDprofessional Newsletter

You will receive a confirmation e-mail. Unsubscribe anytime.